After rolling shutter doors entered the Chinese market, more functions were developed, such as electric shutter doors and crystal shutter doors. Of course, different shutter doors have different installation methods, so today Xiaobian will tell you about the shutter installation method and its installation procedure. First, the electric shutter door installation method 1. First draw the line, based on the drawings, according to the need to install the line on the threshold to be marked as a marker, draw a good start to calculate the size of the shutter door, select the appropriate shutter door. It should be noted that the height of the door frame is higher than the height of the door when drawing lines. 2. Secondly, fix the door frame. Before fixing the door frame, remove the previous fixed board and reserve grooves on the ground on both sides of the hole. Weld the iron foot of the door frame and the iron plate embedded in it and use concrete. It is sealed. 3. At the end, it is better to install the roller shutter door into the door frame. However, during the installation, it should be noted that the above connection must be tight and firm so as to avoid accidental use. When the two sides are connected, it is necessary to form a whole with the wall body, and to ensure the sealing, followed by painting paint, these can be completed to test the use of the next shutter door. Second, the crystal shutter door installation method 1. First, fix the motor on the main board, and fix the manual chain on the motor's wheel and gear, then shake the handle to see if it will be reversed. 2. Then use a ruler to measure the main board and sub board, mainly depends on the size, specifications are not in line with the requirements, and marked a horizontal line on the same axis, and then in the horizontal line drilling, after the first rolling shutter The center of a curtain is fixed to the hole in the shaft. 3. After the roller shutter curtain has been put into use, seal it on both sides with a sealing head, then pull it with a rivet and pry it on the side while perforating the curtain. Then use the screw rod to put the curtain and The shafts are closely connected, and finally the curtains of the rolling shutters are leveled to ensure the safe and rational use of the rolling shutters. Then, the shutter door is raised and lowered back and forth to detect its installation quality and safety. Third, fire shutter doors installation method 1, according to the design model, check the product specification and electrical schematics. Check product surface treatment and accessories. Measure the basic dimensions of various parts of the product. Check whether the opening of the door matches the size of the rolling shutter door; whether the position and quantity of the embedded part of the guide rail and bracket are correct. 2. Measure the elevation of the hole and pop the two guide rails and the center line of the reel. 3. Solder the plate to the embedded iron plate, fix the left and right brackets of the reel with screws, and install the reel. The drum should be flexible after installation. 4. Install reducer and transmission system. 5. Ansang Electric Street System. 6, empty test. 7. Install the pre-assembled curtain on the reel. 8, install the guide rail. According to the position specified on the drawings, the two sides and the upper rails are welded to the wall embedded parts and welded to the body, and each rail should be in the same vertical plane. 9. Install the water curtain spray system and connect it to the general control system. 10. Test run. First try to run by hand, then open and close the motor several times, adjust to no stuck, block and abnormal. Fourth, rolling shutter installation considerations There are not many installation steps. We must pay attention to the installation of technology and experience. Therefore, it is recommended that you do not install it yourself. To find a professional to install is the best method. If you want to install it yourself, after all, there are many small details that will be ignored, or the installation is not precise enough to completely guarantee its security. Xiao Bian summary: Well, the above content is about the rolling shutter installation method and the specific steps of installation, if you want to understand the knowledge about the installation of rolling shutter , read carefully read the contents of the above small series, I believe can provide you with effective help . Best of all, I hope this article will help everyone. Rolling shutter installation ZhiPu chi's company is the best of the domestic molybdenum processing enterprises, according to the customer's requirement to customize the production of various specifications of the Molybdenum Target.We use is the best of the domestic high-quality raw materials, first-class production technology, the top production equipment.It is mainly used for single crystal furnace thermal field Molybdenum Target Molybdenum Target,Good Stability Molybdenum Target,Molybdenum Target With Smooth Surface,High Density Molybdenum Target Baoji Zhipu Non-Ferrous Metals Processing Co., Ltd. , http://www.czpmow.com
