Plate Tile Glass Decoration Cement Wallpaper Marble Decoration Partition Home Wallpapers Glass Tiles Marble Tiles Craft Glass Doors Glass Doors Bathroom Tiles Bathroom Doors Bathroom Tiles Bathroom Color Toilet Door Size Bathroom Size Toilet Interval Home Decoration Home Tile Glue Decoration Home Tile Specification Furniture Handle,Exterior Door Handle,Nordic Brushed Gold Handle,Space Aluminum Alloy Handle Guangzhou Junpai Hardware Co., Ltd , https://www.junpaihardware.com
First, paste type wall surface refers to wallpaper, wall cloth and other wall paper.
(1) The structure of the paste type wall: The wall is plastered with cement mortar to make the wall smooth. After drying, puttying and sanding with sandpaper, then paste the wallpaper with 107 glue or other adhesive.
(2) The main process of applying wallpaper and wall covering is to sweep the grass roots, fill gaps, and put plaster joints at the joints of gypsum boards, putty, matte paper, full scraping putty, smoothing, and applying moisture-proof agent to the bottom of brushing. Glue→wall elasticity→wallpaper immersion→wallpaperã€primary coating adhesive→wall paper cutting and gluing→wall affixing, patchwork stitching, lap jointing, pairing flower→crushing adhesive air bubble→wiping glue→trimming .
(3) Key points for applying wallpapers and wall coverings:
1. The grass-roots treatment must be cleaned, smooth, and smooth. The moisture-proof coating should be painted evenly and not too thick. (1) Concrete and Plastering: The wall surface is cleaned and the surface cracks and pits are leveled with putty. Full of putty, polished flat. Determine the number of scraping passes as needed. (2) Wood base layer: The wood base layer should be planed without burrs, flaws or exposed nail heads. Seams and nails are filled with putty. Full of putty, polished smooth. (3) Gypsum board base: gypsum board joints are treated with caulking putty and fastened with joints. Putty on the surface. Brushing primer is generally used 107 glue, primer at once survived, but there can be no omission.
2. In order to prevent wallpaper and wall cloth from falling off, apply a layer of moisture-proof paint.
3. Play vertical and horizontal lines to ensure that wallpapers and wall coverings are horizontal and vertical with correct patterns.
4. When the plastic wallpaper meets the water, the glue will swell. Therefore, it is necessary to moisten the paper with water to fully inflate the plastic wallpaper. The wallpaper, wall covering, etc. of the glass fiber base material will not expand or contract with water, and the paper will not need to be moistened. Composite paper wallpaper and textile fiber wallpaper should not be stuffy.
5. After pasting, press the adhesive on the wallpaper to leave no bubbles, and the extruded glue should be cleaned in time.
(4) Precautions:
1. Wall base moisture content should be less than 8%.
2. The flatness of the wall is checked with a 2-meter ruler, and the height difference does not exceed 2 mm.
3. When the patchwork is applied, the pattern and the back patchwork are matched so that the top and bottom patterns match.
4. It is forbidden to patch seams at the corners of the sun. The wallpaper must be wrapped over 20 mm above the sun's corner.
5. When glass fiber wall cloth and non-woven wall cloth are applied, the adhesive cannot be applied on the back, and the adhesive is brushed on the base layer. Because the wall cloth has small pores, the adhesive will print through the surface and appear glue marks, affecting the appearance.
Overlay wall decoration process flow:
1. The construction of wooden siding, wood siding, wooden siding, and wooden wall skirts. Anticorrosive wood bricks are embedded in the wall, the wood dragon skeleton is fixed on the wood bricks, and then the panel is nailed or glued to the wood dragon skeleton. The cross section of the wooden keel is 20-40 mm × 40-50 mm, and the spacing of wood keel is 400-600 mm.
2. The construction process flow of wood siding and wood skirts: The treatment of the wall surface → the elastic line → the production of the wood skeleton → the fixing of the wooden skeleton → the decorative panel → the installation of the closing line
3. Construction points:
(1) The wall surface must be flat. If the wall leveling error is within 10 millimeters, plastering can be used; if the error is greater than 10 millimeters, a wooden block can be added between the wall and the keel.
(2) According to the height of the siding board and the size of the room, nails are to be made through the bones, the whole piece or the pieces, and the skirting board is installed at the bottom of the wooden wall skirt. The skirting board is fixed on the lining board and the wall board. The height of the skirting board is 150 mm. Wood lines are fixed to the wainscot.
(3) According to the panel thickness to determine the size of wood keel, transverse keel is generally about 400 mm, vertical keel is generally 600 mm. When the panel thickness is more than 1 mm, the horizontal keel spacing can be appropriately enlarged.
(4) When studs are nailed, the top of the wainscot is to be leveled and the size of the wood bead must be the same.
(5) After the wooden skirt has been installed, it shall be immediately treated with a veneer and brushed with clear oil to prevent other types of work from contaminating the board.
4. Matters needing attention: the wall is damp, should be dry after construction, or do moisture treatment. First, you can do a damp-proof layer on the wall; second, you can leave ventilation holes on the lining board and under the wall; and third, you can pick out the wood bricks inside the wall to make the panel, wood keel and wall away from a certain distance, and avoid moisture. Effect of the panel. Two corners of the wall at the corner of Yin and Yang must be nailed wooden keel. If varnish is applied, panels of the same species, colour and pattern should be selected.
Stone wall decoration process:
(A) natural granite, marble wall structure and construction techniques natural granite, marble plate wall structure: natural stone is heavier, in order to ensure safety, generally adopt double insurance method, that is, the plate and the base layer are tied with copper wire, and then watered Mud mortar. The veneer sheet and the structural wall are separated by 3 to 5 centimeters. As a grouting joint, the height of each infusion is about 20 centimeters after pouring, and the infusion is continued after solidification. Construction process of natural granite and marble plate wall: Primary treatment → installation of basic steel mesh → plate drilling → banding plate → grouting → caulking → polishing.
(II) The construction and construction process of the quartzite wall The construction and construction process of the quartzite wall can be pasted in a similar way to the glazed tile. Bluestone has a high water absorption rate, and it must be soaked with water before it is applied. For home decoration, small size stone and man-made stone can be used for reference.
Veneer decoration basic process flow:
1. Paste the glazed tiles: Grassroots cleaning → Wipe the base ash → Select bricks → Soak → Bricks → Stretch → Paste standard points → Paste tiles → Scrape → Wipe → Clean.
2. Paste the ceramic tile: Clean the base → wipe the base gray → line the brick line → paste → remove the paper → wipe the seam.
3. Construction points When the grassroots is dealt with, all types of dirt on the wall should be cleaned and watered and moistened one day in advance. The concrete wall surface should be chiseled to remove the raised part, cut the base layer, and clean the floating ash. Or use 107 cement cement mortar to pull hair. After rubbing the base ash, when the bottom layer is 6 to 70% dry, the line of bricks is arranged. Paste standard points must be pasted before the official paste, to control the smoothness of the paste surface, the operation should be used at any time to check the flatness by the ruler, uneven, not straight, to remove the re-sticky. Tiles must be soaked in clean water for more than two hours before they are affixed. Tiles should not be bubbling and should be taken out for drying. When sticking and sticking, it encounters pipelines, lighting switches, and supporting devices for bathroom equipment. It must be cut and matched with the entire brick cover. After affixing, wipe the surface with a cotton thread and then wipe with a white grout.
4. Note:
1. The grassroots must be cleaned up and there must be no floating soil or floating dust. The old wall surface will be cleaned of the original mortar surface.
2. Tiles must be soaked and dried. Because the drying board is plastered, the moisture of the mortar will be quickly sucked away by the plates, causing dehydration of the cement mortar, affecting the setting and hardening of the mortar, and problems such as emptying and lifting.
Construction process of wooden keel partition wall:
1. Construction procedures for the wooden keel partition wall Clean up the ground floor → line, find the rules → In the ground with bricks, cement mortar to make the pillow belt (also known as the kick base) → elastic line, back to the ceiling and the main structure wall → The vertical border of the wall bars → installation along the edge, along the edge of the surgery → vertical partition keel → nail horizontal keel → cover panel, set aside the socket location and set up reinforced wood → cover panel processing.
2. Construction Points for Wooden Keel Partition Walls The wood dragon skeleton should use red and white pines with a size of 40 mm × 70 mm. The spacing of the vertical keel is generally between 450 and 600 millimeters. When installing along the ground and along the top, the two ends of the cylinder should be inserted into the brick wall at least l20mm to ensure that the partition wall is firmly connected with the original structural wall. Glass brick partition wall construction process Glass brick partition wall construction points: Glass bricks should be masonry on the basis of two reinforced f6 ~ f8 reinforcement. The base height should not exceed 150mm and the width should be more than 20mm above the glass brick thickness. For the application of metal profiles at the top and the ends of the glass brick dividing wall, the width of the bad mouth should be greater than the thickness of the brick 10~18mm. When the partition length or height is greater than 1500mm, one reinforcing bar is set in every two layers in the vertical direction (two steel bars are provided when the length and height are more than 1500mm), and one reinforcing bar is arranged every three vertical slots in the horizontal direction. Rebar extends not less than 35mm into the slot. The height of glass blocks reinforced with reinforced steel shall not exceed 4m. The ends of the glass partition wall and the two sides of the metal profile shall have a slide joint with a width of no less than 4mm, and the joint shall be filled with linoleum. The glass partition board and the profile shall be left with expansion joints with a width of not less than 10mm to avoid damage to the glass brick partition wall. The top layer of the glass brick should extend into the top metal profile notch 10 ~ 25mm, so as to avoid breaking the glass block due to rigid extrusion. The joint between glass tiles shall not be less than 10mm and not more than 30mm. The joints between glass bricks and profiles, profiles and buildings shall be sealed with elastic sealant.
Mirror glass wall construction process flow:
1. Mirror glass wall construction. Glass fixing method: (1) Drill a hole in the glass, and fix the glass on the wooden skeleton and the backboard with chrome screws and copper screws. (2) Press the glass with a bead of hardwood, plastic, metal, etc. (3) The glass is glued to the backing plate with epoxy resin.
2. Mirror glass installation process: Clean the base → nail wood dragon skeleton → nail liner → fixed glass.
3. Note: (1) The thickness of the uniform glass should be 5~8mm. (2) Do not hammer or shake when installing. Remove the safety when it is not suitable.
Wall decoration is one of the "most facades" of the home improvement. The majority of home improvement owners should thoroughly understand the process flow in this area: