Operational flow description of the elastic impact tester (1) Test preparation: The Elongated Bidet Toilet Seat is indeed a bathroom fixture that offers advanced hygiene and comfort functions. Here are some additional details about its features: Elongated Bidet Toilet Seat, Electronic Bidet Cover, Elongated Toilet Seat, Bidet Function Toilet Seats Guangdong Fabia Intelligent Technology Co., Ltd , https://www.fabiaintelligent.com
1) Visual lens: The magnification is 10 times, and it is self-prepared.
2) Requirements for the test panel: Unless otherwise agreed, the substrate shall be metal and meet the requirements of the standard. The test plate shall be flat and free of deformation and have a thickness of at least 0.25 mm. The dimensions of the test panels shall be tested at least on 5 different parts of the board. Each part shall be no less than 20 mm from the edge of the board, and the distance between the parts shall not be less than 40 mm. The treatment, painting and drying of the test panels shall be carried out in accordance with the prescribed methods. The thickness of the coating shall also be measured as specified. The test shall be carried out at the site to be tested or as close as possible to the test site. Only test panels with a film thickness value not greater than 10% of the specified or agreed film thickness may be used.
3) Unless otherwise agreed, the test shall be carried out at (23 ± 2) °C and (50 ± 5)% relative humidity.
4) Select the appropriate mold base to fit the hole in the base (5) according to the required standard.
5) Select the corresponding weight according to the selected mold base and place the weight from the top of the pipe (1).
6) Place the height limit ring (2) from the top of the pipe and fix it with screws.
7) Adjust the instrument level by adjusting the horizontal foot (6) and the horizontal bubble (7).
(2) Test steps:
a. Pass/fail test:
1) Adjust the height of the height limit ring (2) so that the specified scale meets the specified drop weight height. If necessary, attach a depth control ring, the total thickness of the depth control ring can meet the indentation depth agreed or otherwise specified by both parties.
2) Place the test plate on the mold base so that the paint is facing up or down, so that the indentation can be concave or the bar coater is convex, and the hand wheel (3) is turned to make the compression sleeve ( 8) Press the test plate and loosen the weight to drop it onto the test plate.
3) Check the coating with a lens to see if the coating has cracked or peeled off from the substrate and if the substrate has cracked.
4) Repeat the test four times at different positions of the test plate (a total of 5 drop points). If at least 4 test points are not cracked or peeled off from the substrate, the coating is acceptable.
b. Grading test:
1) Adjust the height of the height limit ring (2) so that the specified scale exactly meets the specified drop weight height, at which height should not be expected to be damaged. If necessary, attach a depth control ring, the total thickness of the depth control ring can meet the indentation depth agreed or otherwise specified by both parties.
2) Place the test plate on the mold base so that the paint is facing up or down, so that the indentation can be concave or convex, and the hand wheel (3) is rotated to press the compression sleeve (8) against the test plate. Loosen the weight and let it fall onto the test panel.
3) Remove the test plate from the device and observe the cracking of the coating in the impact zone. If there is no obvious crack, operate at a higher height until the crack is observed, according to the weight used, 1kg ( 2 lb.), height increments are multiples of 25 mm (1 inch) or 25 mm (1 inch). If the weight is still not cracked at the maximum height permitted by the instrument, repeat the operation with 2 kg (4 lbs).
4) Once the crack is observed at a certain height of the agitator, proceed as follows: at this height and the height of 25 mm (1 inch) and 25 mm (1 inch) lower than this height, each drop to the test plate 5 times, that is, 15 drops. The tests were carried out in any manner so that all impacts at the same height were not continuous or only tested on a test panel tinplate.
5) Use a lens to check the coating for cracking or peeling from the substrate, and list the results of 15 passes and damage. A comprehensive quality/height report that changes the results of most of these damages is used as the end point of impact damage.
6) If the end point cannot be obtained according to the above operation, then (4), (5), and two steps are performed again, and all three heights are used as applicable values ​​to ensure that the end of the impact damage is replaced by the range of the test height.
For more information on the impact tester, please visit: high and low temperature test chamber http://
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
PP Plastic Material: The Bidet Seat is made of durable and easy-to-clean PP plastic. This material is known for its strength and resistance to wear and tear, ensuring the longevity of the bidet seat.
Warm Water Cleaning System: The bidet seat features a warm water cleaning system that provides a gentle and soothing cleansing experience. The adjustable temperature control allows users to customize the water temperature according to their preferences.
Adjustable Water Pressure: Users can adjust the water pressure of the bidet spray to achieve their desired level of cleansing. This feature ensures a comfortable and effective cleaning experience for each individual.
Heated Seats: The bidet seat includes a heated seat function, providing warmth and comfort during use, especially in colder environments. The temperature of the seat can be adjusted to suit personal preferences.
Drying Function: Some bidet seats offer a drying function, which eliminates the need for toilet paper after cleansing. This feature provides convenience and a more hygienic alternative to traditional drying methods.
Hygienic and Comfortable Experience: The bidet seat's comprehensive features, such as warm water cleaning, adjustable pressure and temperature, heated seats, and drying function, contribute to a more hygienic and comfortable bathroom experience. It eliminates the need for toilet paper, reducing waste and promoting better hygiene practices.
Sleek and Modern Design: The bidet seat's sleek and modern design adds a touch of sophistication to any bathroom decor. It blends seamlessly with the existing fixtures and enhances the overall aesthetics of the bathroom.
Investing in an Elongated Bidet Toilet Seat is a practical choice for individuals who prioritize hygiene and comfort in their daily lives. It offers advanced features that enhance the bathroom experience and promote better personal hygiene practices.