Tiles are the top three items in the decoration building materials, and its quality is more difficult to judge. How can you see through the inferior tiles at a glance? The first step: pouring water The water absorption rate reflects the density of the tile, and indirectly reflects the hardness of the tile, but one thing to note is that the tile is not as low as the water absorption rate. The water absorption test here is a test for tiles in the living room, bedroom, walkway, etc. First, pour water onto the front and back sides of the tile, carefully observe the water penetration. If you buy polished tiles, water immediately I was sucked in, congratulations, and encountered poor quality polished tiles. In general, the slower the water absorption, the greater the density of the tile; conversely, the faster the water absorption, indicating that the density is sparse, and the inherent quality is superior. In addition, the hardness of the tile was observed, and the tile was excellent in hardness, toughness, and not easy to be broken. Scrub the edges of the tiles with each other to see if the broken pieces are fine or loose, hard, brittle or soft, leaving scratches or scattered powder. If the former is the top, the latter is the quality. difference. Step 2: Pay attention to surface flatness After the surface of the tile is laid up, there is an uneven condition. There are two aspects. One is that the decoration master is not at home; the second is the quality of the tile itself. When the tiles are not yet laid, it is recommended that you first look at the flatness of the tile surface. After confirming the correctness, please call the decoration master to start, so as to avoid the aesthetic problems caused by the tile problem, and avoid the master to make his own craft. The problem is shirking to the tile problem. The color of the tiles should be uniform, the surface finish and flatness should be good, the surrounding rules and patterns should be complete, and four or five pieces should be taken out from a box to see if there are any defects such as color difference, deformation, lack of edges and corners. The third step: measurement The straightness test of the corners of the tile is to see if the overall layout of the tile is neat and the gap size is consistent. At this time, we pick up a few tiles and put them on the flat ground. Pay attention to see if the gap between the tiles and the tiles is the same. The corners of the tiles can be pieced together and not too much. If the straightness of the corners is not regular, the tiles that are laid out must not be neat, which affects the overall paving effect. Everyone should pay attention. The higher the accuracy of the length of the tile, the better the effect after the paving. Buying high-quality tiles is not only easy to construct, but also saves working hours and accessories. Use a tape measure to measure the size of each tile around the difference, the highest accuracy is the top grade. Whether the size is the standard is the key to judging the advantages and disadvantages of the tile. Use a tape measure or a caliper to measure the diagonal and the size and thickness of the tile. Step 4: Get a smudge look This step mainly investigates the stain resistance of tiles. It is important to know that tiles will accompany us for a long period of time. If it is not easy to clean if it is dirty, it is estimated that it will not be three or four years. Even if you don't want to stay in a dirty home, you can't wait to lift these tiles right away. In fact, it is very simple to do this anti-fouling test. You only need to write the words "Go here" on the surface of the tile. Wait for a while to see if it is easy to clean. If you leave ink, I suggest you still have another Choose a good one. Step 5: Scratch! Scratch! Scrape! Nowadays, the tiles have undergone a series of innovations in wear resistance. Whether it is polished tiles, microcrystalline stones, full-glazed glazes, antique bricks, etc., there is a qualitative leap, so we can judge whether the surface is wear-resistant or not. Just pick up the knife in your hand and scrape it on the surface of the tile to see if it will scrape off the glaze on the tile surface. If you can't bear such a small scratch, you can conclude that this tile is not A good partner who can stay with us for a long time. Step 6: Listen to the sound When tapping with a hard object, the crisper the sound, the higher the degree of porcelain and the better the quality. You can also use the left thumb, forefinger and middle finger to clip the corner of the tile and hang it down easily. Use your right index finger to tap the middle and lower part of the tile. For example, the sound is clear and pleasing to the top. For example, the sound is dull and turbid, and the smashing sound is the next product. Good ceramic tiles, the sound is crisp, indicating that the porcelain content is high. It shows that there are cracks in the brick. [Follow the WeChat public number " Jiuzheng Ceramics Network" ; pay attention to courtesy, scan code to send millions of business opportunities! Jiuzheng ceramics network exchange group: 80123558 】
New student desks and chairs, you can lie down and lift
Two desktops have different options
School Furniture,Student desks and chairs,Nap Chair,Kids study desk,Student lunch desk. FOSHAN CITY LESHUN RONGHUI FURNITURE CO.LTD , https://www.ronghuifurniture.com
The desktop adopts a secure rounded corner design,Hidden school bag hook.
The front edge of the seat and cushion adopts a wave design, which effectively reduces the pressure on the hips and waist.
